HAZARDS & PRECAUTIONS

DANGER

Highly flammable liquid and vapor.
May be fatal if swallowed and enters airways.

Causes skin irritation. May cause an allergic skin reaction.

Causes serious eye irritation. Suspected of causing genetic defects. May cause cancer.

Suspected of damaging fertility or the unborn child.
Causes damage to organs through prolonged or repeated exposure.

Keep away from heat, sparks, open flames, hot surfaces. No smoking. Keep container tightly closed. Ground container and receiving equipment. Use explosion-proof electrical, ventilating and lighting equipment. Use only non-sparking tools. Take precautionary measures against static discharge. Wear protective gloves, protective clothes, eye protection and face protection. Wash thoroughly after handling. Do not breathe vapors. Contaminated work clothing should not be allowed out of the workplace. Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not eat, drink or smoke when using this product. Avoid release to the environment.

FIRST AID

IF ON SKIN (or hair): Take off immediately all contaminated clothing and wash before reuse. Rinse skin with water or shower. If skin irritation or rash occurs: Get medical attention.

IF SWALLOWED: Immediately call a POISON CENTER or doctor. Do NOT induce vomiting.

IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.

IF exposed or concerned: Call a POISON CENTER or doctor and get medical attention.

In case of fire: Use alcohol resistant foam, carbon dioxide or dry chemical to extinguish.

 Store locked up in a well-ventilated place. Keep cool.

Dispose of in accordance with Federal, State and local regulations.

DIRECTIONS FOR USE

For optimal performance, bring all components to room temperature prior to use. Add a ribbon of ProFil Hardener to a golf ball sized amount of ProFil Compound. Mix to a uniform color. Spread a thin layer onto the surface. NOTE: Do not apply over fresh or uncured coatings. Break with 80-180 grit sandpaper after approximately 10 to 15 minutes. Finish sanding to desired smoothness. Do not return unused material to can.

For copies of the SDS and Technical Data Sheets, contact Hawk or visit www.hawklabs.com.

IsoFree® Lo 6550 Resin

Gloss Clear – Stock #655056V11LO

Gloss White – Stock #655046V11LO

Old World White – Stock #655006V11LO

Celestial White – Stock #655016V11LO

Perfect White – Stock #655026V11LO

 

 

Download Full Label

 

 

HAZARDS & PRECAUTIONS

Flammable liquid and vapor.

May be fatal if swallowed or enters airways.

Causes skin irritation.

Causes serious eye damage.

Harmful if inhaled.

May cause respiratory irritation.

Suspected of causing cancer.

May cause damage to organs through prolonged

or repeated exposure.

 

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Ground and bond container and receiving equipment. Use explosion-proof electrical, ventilating and lighting equipment. Use non-sparking tools. Take action to prevent static discharges. Wear protective gloves, protective clothing, eye protection and face protection. Wash thoroughly after handling. Do not breathe mist, vapors or spray. Use only outdoors or in a well-ventilated area. Obtain special instructions before use. Do not handle until all safety precautions have been read and understood.

FIRST AID

IF ON SKIN (or hair): Take off immediately all contaminated clothing and wash before reuse. Rinse skin with water or shower. If skin irritation occurs: Get medical attention.

IF SWALLOWED: Immediately call a POISON CENTER or doctor. Do NOT induce vomiting.

IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER or doctor.

IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER or doctor if you feel unwell.

IF exposed or concerned: Get medical attention.

In case of fire: Use water fog, foam, dry chemical or carbon dioxide to extinguish.

Store locked up in a well-ventilated place. Keep container tightly closed and cool.

Dispose of in accordance with Federal, State and local regulations.

DIRECTIONS FOR USE

For optimal performance, bring all components to room temperature  and SHAKE WELL prior to use.

Mix 1 part IsoFree Lo 6550 Resin and 1 part IsoFree Lo 6550 Catalyst.

For copies of the SDS and Technical Data Sheets, contact Hawk or visit www.hawklabs.com.

IsoFree® Lo 6550 Catalyst

Stock #655406V12LO

 

 

Download Full Label

 

HAZARDS & PRECAUTIONS

DANGER

Highly flammable liquid and vapor.

Causes skin irritation.

May cause an allergic skin reaction.

Causes serious eye irritation.

May cause respiratory irritation.

May cause drowsiness or dizziness.

 

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Ground and bond container and receiving equipment. Use explosion-proof electrical, ventilating and lighting equipment. Use non-sparking tools. Take action to prevent static discharges. Wear protective gloves, protective clothing, eye protection and face protection. Wash thoroughly after handling. Avoid breathing mist, vapors or spray. Contaminated work clothing should not be allowed of the workplace. Use only outdoors or in a well-ventilated area.

FIRST AID

IF ON SKIN (or hair): Take off immediately all contaminated clothing and wash before reuse. Rinse skin with water or shower. If skin irritation occurs: Get medical attention.

IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.

IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER or doctor if you feel unwell.

In case of fire: Use water spray, dry chemical, carbon dioxide or alcohol foam to extinguish.

Store locked up in a well-ventilated place. Keep container tightly closed and cool.

Dispose of in accordance with Federal, State and local regulations.

DIRECTIONS FOR USE

For optimal performance, bring all components to room temperature and SHAKE WELL prior to use.

Mix 1 part IsoFree Lo 6550 Resin and 1 part IsoFree Lo 6550 Catalyst.

For copies of the SDS and Technical Data Sheets, contact Hawk or visit www.hawklabs.com.

IsoFree® Lo 6550 Medium Reducer

Stock #65506V12LO

 

 

Download Full Label

 

HAZARDS & PRECAUTIONS

DANGER
Highly flammable liquid and vapor.
Causes mild skin irritation.
Causes serious eye irritation.
May cause respiratory irritation.
May cause drowsiness or dizziness.
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Ground and bond container and receiving equipment. Use explosion-proof electrical, ventilating and lighting equipment. Use non-sparking tools. Take action to prevent static discharges. Wear protective gloves, protective clothing, eye protection and face protection. Wash thoroughly after handling. Avoid breathing mist, vapors or spray. Use only outdoors or in a well-ventilated area.

FIRST AID

IF ON SKIN (or hair: Take off immediately all contaminated clothing. Rinse skin with water or shower. If skin irritation occurs: Get medical attention.

IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.

IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER or doctor if you feel unwell.

In case of fire: Use water spray, dry chemical, carbon dioxide or alcohol foam to extinguish.

Store locked up in a well-ventilated place.
Keep container tightly closed and cool.

Dispose of in accordance with Federal, State and local regulations.

WARNING: This product can expose you to chemicals including titanium dioxide, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.

DIRECTIONS FOR USE

For optimal performance, bring all components to room temperature and SHAKE WELL prior to use.

For use with IsoFree Lo 6550 Resin, mix 1 part resin with 1 part IsoFree Lo 6550 Catalyst and reduce as needed with IsoFree Reducer.

For copies of the SDS and Technical Data Sheets, contact Hawk or visit www.hawklabs.com.

GlasTech® 9000 Tints

Lamp Black – Stock #90086V14
Q Violet – Stock #90176V14
Red Oxide – Stock #90186V14
Organic Orange – Stock #90196V14
Organic Yellow – Stock #90206V14
Yellow Oxide – Stock #90226V14
Phthalo Green Y – Stock #90236V14
Phthalo Blue R – Stock #90246V14
Burnt Umber – Stock #90256V14
Q Red – Stock #90266V14

Download Full Label

 

HAZARDS & PRECAUTIONS

WARNING
Flammable liquid and vapor.
Causes skin irritation.
Causes serious eye irritation.
May cause drowsiness or dizziness.
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Ground and bond container and receiving equipment. Use explosion-proof electrical, ventilating and lighting equipment. Use non-sparking tools. Take action to prevent static discharges. Wear protective gloves, protective clothing, eye protection and face protection. Wash thoroughly after handling. Avoid breathing mist, vapors or spray. Use only outdoors or in a well-ventilated area.

FIRST AID

FIRST AID: IF ON SKIN (or hair): Take off immediately all contaminated clothing and wash before reuse. Rinse skin with water or shower. If skin irritation occurs: Get medical attention.

IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.

IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER or doctor if you feel unwell.

In case of fire: Use foam, carbon dioxide or dry chemical to extinguish.

Store locked up in a well-ventilated place. Keep container tightly closed and cool.

Dispose of in accordance with Federal, State and local regulations.

DIRECTIONS FOR USE

For optimal performance, bring all components to room temperature and SHAKE WELL prior to use.

Mix 1 part IsoFree® Lo 6550 Resin with 1 part IsoFree Lo 6550 Catalyst, then add up to 2% GlasTech 9000 tint resin by drops to achieve desired shade.

QuickPrep+™ Universal Bonding Agent

Stock #90716V12

Download Full Label

 

HAZARDS & PRECAUTIONS

DANGER
Causes serious eye irritation.
Highly flammable liquid and vapor.
If medical advice is needed, have product container or label at hand. Keep out of reach of children. Read label before use.
Wash thoroughly after handling. Wear protective glove, clothing, eye and face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Keep container tightly closed. Ground container and receiving equipment. Use explosion proof electrical, ventilating, lighting equipment. Use only non-sparking tools. Take action to prevent static discharges.

FIRST AID

IF SWALLOWED: Immediately call a POISON CENTER or doctor. Rinse mouth. Do NOT induce vomiting.

IF ON SKIN (or hair): Take off immediately all contaminated clothing and wash before reuse. Rinse skin with water or shower. Immediately call a POISON CENTER or doctor.

IF INHALED: Remove person to fresh air and keep comfortable for breathing.

IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Absorb spillage to prevent material-damage.

Store locked up in a corrosive resistant container with a resistant liner.

Dispose of in accordance with Federal, State and local regulations.

DIRECTIONS FOR USE

For optimal performance, bring all components to room temperature and SHAKE WELL prior to use.

Using a lint-free cloth, wipe QuickPrep+ on repair area in straight, even wiping motion vertically, then repeat horizontally. Do not over-apply or allow it to puddle. Allow to dry 10-20 minutes prior to applying primer. Must be re-applied after 12 hours if coating hasn’t been applied.

Repair Blender

Stock #90534V12

Download Full Label

 

HAZARDS & PRECAUTIONS

DANGER

Highly flammable liquid and vapor.

Harmful if swallowed.

May be fatal if swallowed and enters airways.

Harmful in contact with skin.

Causes skin irritation.

Harmful if inhaled.

May cause drowsiness or dizziness.

Suspected of damaging fertility or the unborn child.

May cause damage to organs through prolonged or repeated exposure.

 

Keep away from het, hot surfaces, sparks, open flames and other ignition sources. No smoking. Ground and bond container and receiving equipment. Use explosion-proof electrical, ventilating and lighting equipment. Use non-sparking tools. Take action to prevent static discharges. Wear protective gloves, protective clothing, eye protection and face protection. Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Do not breathe mist, vapors or spray. Use only outdoors or in a well-ventilated area. Obtain special instructions before use. Do not handle until all safety precautions have been read and understood.

FIRST AID

IF ON SKIN (or hair): Take off immediately all contaminated clothing and wash before reuse. Rinse skin with water or shower. Call a POISON CENTER or doctor if you feel unwell. If skin irritation occurs: Get medical attention.

IF SWALLOWED: Immediately call a POISON CENTER or doctor. Rinse mouth. Do NOT induce vomiting.

IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.

IF INHALED: Remove person to fresh air and keep comfortable for breathing.

IF exposed or concerned: Get medical attention.

Store locked up in a well-ventilated place. Keep container tightly closed and cool.

Dispose of in accordance with Federal, State, and local regulations.

DIRECTIONS FOR USE

For optimal performance, bring all components to room temperature prior to use. Remove any halo effects over the surface that has been previously sprayed with any Hawk Topcoat System. Apply by spray. For smaller repairs, use an airbrush.

For copies of the SDS and Technical Data Sheets, contact Hawk or visit www.hawklabs.com.